Home Entertainment

 

Tech Tips: Evaluating Speaker Specifications




Your ears are more important than the numbers.

Canton CD220

A reader wrote in to our Ask-a-Pro forum for help with understanding speaker specifications. The reader asked: “What are the best spec’s to look at when buying surround sound speakers. If a speaker’s frequency response is 47hz - 30khz and another is 58hz - 30khz which is better and why?”

Our resident audio authority Bob Archer, from CE Pro Magazine, offered this advice:

Unfortunately, determining a speaker’s applicability to a given installation is not as easy as looking at the specifications.

Frequency response can be a useful number in giving you a guideline in how dynamically the speaker will perform (it’s ability to create low frequency, midrange and high frequency content) , but there are other specs such as efficiency and impedance that are important too.

With the numbers you’ve provided (speaker A 47Hz to 30kHz vs. speaker B 58Hz to 30kHz) the frequency response numbers tell us that in theory speaker A plays a little bit deeper than speaker B. That is of course as I mentioned a guideline that’s subject to factors such as the room environment the speakers are placed in.

Speaker response, along with impedance, speaker sensitivity rating and to a lesser extend power handling are to many the specifications worth looking at.

Quickly going over these numbers: Impedance is the “load” the speaker presents to the amplifier. Look for numbers such as 8 ohms as this indicates the speaker is easier to drive than a 4 ohm speaker.

Sensitivity indicates how easily a speaker converts power into sound. In theory a speaker rated with a 91dB level should play twice as loud as a speaker rated at 88dB. So, for example it would take a 300 watt amp to drive an 88dB speaker to play as loud as a 91dB sensitive speaker driven by a 150 watt amplifier.

Power handling is a number that everyone defines differently, so this can be a tough number to go by, but in theory you wouldn’t want to use a 400 watt amp to drive a speaker rated to a maximum power handling of 80 watts.

Read Acoustics Matter: Tips for Home Theater Speakers

The most important factors to go by when evaluating a speaker for rear surround is the application in which you intend to use the product. There are three basic types of rear surround speakers: direct radiating, bipolar and dipole. Direct radiating speakers are traditional speakers the disperse sound directly from their front baffles (where the speaker drivers are located). Bipolar speakers are designed to disperse sound in a spherical pattern to fill a larger space and dipole speakers look nearly identical to bipolar speakers and they accomplish a similar goal of filling wide spaces, but they work through a dispersion pattern that looks like a figure-eight pattern. Bipolar and dipole speakers features drivers on the front and back of their cabinets or if they are specifically designed for rear surround they may have a flat backside that designed to hang on a wall, a front with a midrange/woofer driver and angled sides that employ tweeters that spray higher frequencies to the sides.

Read more about bipole and dipole speakers here.

The major difference with a dipole and bipolar speaker is that a dipole’s side or rear drivers are wired out of phase from the front drivers. A bipolar speaker’s drivers are all wired in phase with one another.

Canton CD360f

Your goal will be through the use of specifications and application scenarios will be to determine if you want a direct radiating speaker, which tend to sound more focused or a bipolar or dipole speaker that tend to sound more diffuse, but are capable of filling a larger space with sound.

Have a question about home theater, audio, video, home control, lighting and other consumer electronics? Get your questions answered with Electronics House’s Ask A Pro. To contribute to the Ask-A-Pro forum or to ask for help on the forum, go directly here. Read other popular Ask-a-Pro topics here.

Article courtesy of ElectronicHouse.com

Comments

Post new comment

  • Web page addresses and e-mail addresses turn into links automatically.
  • Lines and paragraphs break automatically.
  • Images can be added to this post.
  • Glossary terms will be automatically marked with links to their descriptions. If there are certain phrases or sections of text that should be excluded from glossary marking and linking, use the special markup, [no-glossary] ... [/no-glossary]. Additionally, these HTML elements will not be scanned: a, abbr, acronym, code, pre.

More information about formatting options

Local Guides

 All Guides
   Alabama
   Alaska
   Arizona
   Arkansas
   California
   Colorado
   Connecticut
   DC
   Delaware
   Florida
   Georgia
   Hawaii
   Idaho
   Illinois
   Indiana
   Iowa
   Kansas
   Kentucky
   Louisiana
   Maine
   Maryland
   Massachusetts
   Michigan
   Minnesota
   Mississippi
   Missouri
   Montana
   Nebraska
   Nevada
   New Hampshire
   New Jersey
   New Mexico
   New York
   North Carolina
   North Dakota
   Ohio
   Oklahoma
   Oregon
   Pennsylvania
   Rhode Island
   South Carolina
   South Dakota
   Tennessee
   Texas
   Utah
   Vermont
   Virginia
   Washington
   West Virginia
   Wisconsin
   Wyoming